AltBerg Svartz Footbeds

AltBerg Svartz Anatomix Absorber Footbeds

AltBerg Svartz Anatomix Absorber Footbeds

£23.39 £19.49 (ex. VAT)
Stock Status: In Stock

Only left in Stock

Alt-Berg Svartz Footbeds
Bookmark and Share

AltBerg Svartz Anatomix Absorber Foot beds

Maximum Shock Absorption -
Improves Arch Support and Foot Stability -
Improves Heel & Achilles Alignment


Size 2 - to fit boot size 2.5 > 4
Size 3 - to fit boot size 4.5 > 6
Size 4 - to fit boot size 6.5 > 8
Size 5 - to fit boot size 8.5 > 10
Size 6 - to fit boot size 10.5 > 12
​Size 7 - to fit boot size 12.5 > 14

Svartz® Anatomic Absorber Footbeds

Specifically designed for running, backpacking, or ‘tabbing’ on rough terrain – especially effective on long descents, where impact on knees and joints needs to be reduced.  The Absorber combines maximum shock absorption with a 3 dimensional underfoot support for maximum foot stability.

This is an excellent foot bed for professional users, long distance walkers, mountaineers, or military who carry backpacks – at speed, over long distances.

Svartz® Anatomic Absorber Footbeds
  • Maximum shock absorption 12.5/32 (Shore A test – scale is 10 to 80 – 10 = maximum cushioning, 80 = minimum cushioning)
  • Covering – Meshtex, a synthetic, breathable material – used by Alt-Berg in Jungle boots, specifically developed for hot, humid conditions
  • Forefoot thickness 4.5/5.0 mm
  • Centre heel thickness 7.5 mm
  • 3 dimensional arch support and domed raise behind metatarsal heads to take pressure off balls of feet during running or walking
Washable at 30 degrees
Sweat Absorber
Breathable Foot bed Cover
Shock Absorption
Flexible
Ankle & Underfoot Support
Better Weight Distribution
Improved Stabilisation

WASHING INSTRUCTIONS

Clean by rubbing gently with a sponge, hot water, and normal soap, then rinse the foot bed surface under a running tap.  This will help flush out any perspiration salts which may have been absorbed into the foot bed fabric.

In extreme conditions, the Anatomic Absorber foot bed may be machine washed – maximum temperature 30°C

DRYING INSTRUCTIONS

Allow to dry naturally in a cool place.

Do not put near heat Do not dry on a radiator

Heat will damage the footbeds.

  • Do not tumble dry
  • Do not dry in sunlight

AltBerg Footbeds Trim To Fit Advice

STEP ONE

(First check the old foot bed is a good fit) Remove old foot bed from the boot  

 AltBerg Svartz Foodbeds Fitting Advice


 

STEP TWO

If the old foot bed is a good fit, use it to mark the Svartz foot bed trimming line

 AltBerg Svartz Footbeds Trimming Advice


 

STEP THREE

The line should be clearly marked.
Add a little bit if the old foot bed was too small. Reduce a little bit if the old foot bed was too tight  



STEP FOUR

Use scissors to trim the Svartz foot bed to the required size



STEP FIVE

Don't cut too much - a full half size is only 6mm! If unsure, trim a bit at a time, you can always cut a little bit more off - but you can't add it back on again



STEP SIX

Put the trimmed foot bed into the boot to replace the old foot bed. CHECK THE FIT -if it is still too tight, mark and trim a little more

  • Brand:
    Alt-Berg
  • Product Code:
    SVARTZ-AA-000
  • Weight:
    0.5kg